【体验】+远程温湿度代码生成SOC方案

kjhkskjhaksd

关于产品的创建请参考某坛友的帖子，【体验】+0基础实现WiFi远程插座
此处不再废话
按照WIFI变长创建新产品
创建如下2个数据点

显示名称	标识名	备注	读写类型	数据类型	数值				枚举	扩展
显示名称	标识名	备注	读写类型	数据类型	分辨率	增量	数据范围最小值	数据范围最大值	选项	长度
温度	temperature		只读	数值	1	-10	-10	50
湿度	humidity		只读	数值	1	0	0	99

在MCU开发里面选择SOC方案，然后选择32M，生成代码下载。
接下来我们采用DHT11来实现温湿度的采集
在项目里面创建如下2个文件，以及文件内容
1，hal_temp_hum.c

#include "driver/hal_temp_hum.h"
#include "osapi.h"

th_typedef_t temphum_typedef;

static void ICACHE_FLASH_ATTR tempHumDelay(unsigned int us)
{
/* Define your delay function */

os_delay_us(us);
}

//Reset DHT11
static void ICACHE_FLASH_ATTR dht11Rst(void)
{
DHT11_IO_OUT;                                              //SET OUTPUT
DHT11_OUT_LOW;                                           //GPIOA.0=0
tempHumDelay(18*1000);                                  //Pull down Least 18ms
DHT11_OUT_HIGH;                                           //GPIOA.0=1
}

static uint8_t ICACHE_FLASH_ATTR dht11Check(void)
{
uint8_t retry=0;

DHT11_IO_IN;                                              //SET INPUT
while (DHT11_IN&&retry<100)                               //DHT11 Pull down 40~80us
{
      retry++;
      tempHumDelay(1);
}

if(retry>=100)
      return 1;
else
      retry=0;

while (!DHT11_IN&&retry<100)                               //DHT11 Pull up 40~80us
{
      retry++;
      tempHumDelay(1);
}

if(retry>=100)
      return 1;                                              //chack error

return 0;
}
static uint8_t ICACHE_FLASH_ATTR dht11ReadBit(void)
{
uint8_t retry=0;
while(DHT11_IN&&retry<100)                               //wait become Low level
{
      retry++;
      tempHumDelay(1);
}
retry=0;
while(!DHT11_IN&&retry<100)                               //wait become High level
{
      retry++;
      tempHumDelay(1);
}
tempHumDelay(40);                                        //wait 40us
if(DHT11_IN)
      return 1;
else
      return 0;
}
static uint8_t ICACHE_FLASH_ATTR hdt11ReadByte(void)
{
uint8_t i;
uint8_t dat=0;
for (i=0; i<8; i++)
{
      dat<<=1;
      dat |= dht11ReadBit();
}
return dat;
}

static uint8_t ICACHE_FLASH_ATTR dht11ReadData(u8 * temperature, u8 * humidity)
{
uint8_t i;
uint8_t buf[5];
dht11Rst();
if(0 == dht11Check())
{
      for(i=0; i<5; i++)
      {
         buf = hdt11ReadByte();
      }
      if((buf[0]+buf[1]+buf[2]+buf[3])==buf[4])
      {
         *humidity=buf[0];
         *temperature=buf[2];
      }
}
else
{
return 1;
}
return 0;
}

uint8_t ICACHE_FLASH_ATTR dh11Read(uint8_t * temperature, uint8_t * humidity)
{
uint8_t ret = 0;
uint8_t cur_i = 0;
uint8_t curTem = 0;
uint8_t curHum = 0;
uint16_t temMeans = 0;
uint16_t hum_means = 0;
ret = dht11ReadData(&curTem, &curHum);
if(0 == ret)
{
      //Cycle store ten times stronghold
      if(MEAN_NUM > temphum_typedef.th_num)
      {
         temphum_typedef.th_bufs[temphum_typedef.th_num][0] = curTem;
         temphum_typedef.th_bufs[temphum_typedef.th_num][1] = curHum;
         temphum_typedef.th_num++;
      }
      else
      {
         temphum_typedef.th_num = 0;
         temphum_typedef.th_bufs[temphum_typedef.th_num][0] = curTem;
         temphum_typedef.th_bufs[temphum_typedef.th_num][1] = curHum;
         temphum_typedef.th_num++;
      }
}
else
{
      return 1;
}
if(MEAN_NUM <= temphum_typedef.th_num)
{
      temphum_typedef.th_amount = MEAN_NUM;
}
if(0 == temphum_typedef.th_amount)
{
      //Calculate Before ten the mean
      for(cur_i = 0; cur_i < temphum_typedef.th_num; cur_i++)
      {
         temMeans += temphum_typedef.th_bufs[cur_i][0];
         hum_means += temphum_typedef.th_bufs[cur_i][1];
      }
      temMeans = temMeans / temphum_typedef.th_num;
      hum_means = hum_means / temphum_typedef.th_num;
      *temperature = temMeans;
      *humidity = hum_means;
}
else if(MEAN_NUM == temphum_typedef.th_amount)
{
      //Calculate After ten times the mean
      for(cur_i = 0; cur_i < temphum_typedef.th_amount; cur_i++)
      {
         temMeans += temphum_typedef.th_bufs[cur_i][0];
         hum_means += temphum_typedef.th_bufs[cur_i][1];
      }

      temMeans = temMeans / temphum_typedef.th_amount;
      hum_means = hum_means / temphum_typedef.th_amount;

      *temperature = (uint8_t)temMeans;
      *humidity = (uint8_t)hum_means;
}

return 0;
}

uint8_t ICACHE_FLASH_ATTR dh11Init(void)
{
/* Migrate your driver code */
PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO5_U, FUNC_GPIO5);
dht11Rst();
os_memset((uint8_t *)&temphum_typedef, 0, sizeof(th_typedef_t));
os_printf("dh11Init \r\n");
return dht11Check();
}
void ICACHE_FLASH_ATTR dh11SensorTest(void)
{
/* Test LOG model */
uint8_t curTem = 0;
uint8_t curHum = 0;
dht11ReadData(&curTem, &curHum);
os_printf("Temperature : %d , Humidity : %d", curTem, curHum);
}

2，hal_temp_hum.h

#ifndef _HAL_HEMP_HUM_H
#define _HAL_HEMP_HUM_H
#include <stdio.h>
#include <c_types.h>
#include <gpio.h>
#include <eagle_soc.h>
/* Define your drive pin */
#define DHT11_GPIO_PIN    5
/* Set GPIO Direction */
#define DHT11_IO_IN       GPIO_DIS_OUTPUT(GPIO_ID_PIN(DHT11_GPIO_PIN))// gpio_output_set(0, 0, 0, GPIO_ID_PIN(DHT11_GPIO_PIN))不可用
#define DHT11_IO_OUT       gpio_output_set(0, 0, GPIO_ID_PIN(DHT11_GPIO_PIN), 0)
#define DHT11_OUT_HIGH    GPIO_OUTPUT_SET(GPIO_ID_PIN(DHT11_GPIO_PIN), 1)
#define DHT11_OUT_LOW    GPIO_OUTPUT_SET(GPIO_ID_PIN(DHT11_GPIO_PIN), 0)
#define DHT11_IN          GPIO_INPUT_GET(GPIO_ID_PIN(DHT11_GPIO_PIN))
#define MEAN_NUM          10
typedef struct
{
uint8_t th_num;
uint8_t th_amount;
uint8_t th_bufs[10][2];
}th_typedef_t;
/* Function declaration */
uint8_t dh11Read(uint8_t * temperature, uint8_t * humidity);
uint8_t dh11Init(void); //Init DHT11
void dh11SensorTest(void);
#endif /*_HAL_HEMP_HUM_H*/

DHT11的数据引脚接在ESP8266的GPIO5上面
然后在主函数和gizwits_product.c里面包含温湿度的头文件，
主函数里面吧初始化写在按键初始化后面
userHandle函数需要加入温湿度采集
温湿度读取的函数是uint8_t ICACHE_FLASH_ATTR dh11Read(uint8_t * temperature, uint8_t * humidity)
返回的第一个参数温度，第二个参数湿度，把返回值赋值给currentDataPoint.valuetemperature和currentDataPoint.valuehumidity即可

【体验】+远程温湿度代码生成SOC方案

kjhkskjhaksd LV2

站长推荐 /3